Nice, but way too difficult. I got a Arduino Uno and I would like to build something like the above, but with much less diodes, e. Further I want to program by myself. Any suggestions? Thank you for sharing your work. It is good to see another description on how to build this cube. The RED version is so cute. You should connect 0. So, a total of nine 0.
This is a very beautiful design. Thank you for this. This I would certainly make during this coming winter. Can I please get the code? I myself can not make such code unfortunately. Such a thing should I study to really made codes. My email: p. That would be so for installation a xxx. It is this that I would like to, The other are listed and I have found such as: arduinocube. May upload on Atmega 32 using Arduino Uno Board, but otherwise??? Download that file and change the extension to.
First, congrats for the project. You did a very aligned eds and cleaned job. This has a professional aspect. I have one question: are you able to sell the PCBs? Does anyone have any experience with this? Is this something that can be fixed? Any help would be greatly appreciated! For that matter, it sounds as though this should be working as I solder in the rows of LEDs one by one or is that not the case, do they need to all be connected for this to work correctly? I have two in at the moment and am seeing that current is flowing through only about half of the resistors on the board.
They can work with vertical layer one by one, make sure the anode pin is connected to the pcb board. Crrently there will no animation if that 3 pin still sorted. Hi, that three pin connected to twenty d ics, so they can be sorted on either one of the d ics, you can refer to the schematic, all d ICs has 3 signal pin connected to the exactly the three you circled.
You may need some flux to clean up the solder. I want to purchase this kit, but I don't want to use the built in controller. Your programming is very, very good. It is much better than mine, but I wish to drive the cube with my own hardware just to challenge myself.
Is the mainboard only 2 layers? If it is, it should be easy for me to modify the board to drive R, G, and B channels independently.
Would you be willing to share the PCB file so I can get an idea of what modifications I'd need to make before I purchase the kit? Hi, I am reselling this item from a supplier, so I don't get the pcb file. But the schematic file is shared on step 6, it was correctly rotue same as the pcb board.
But I extend the main controller parts out to the small stm32 controller board. I think you idea should work if you have the ic data sheet.
Thank you for the fast response. I will go ahead and order from your ebay store. Hopefully I will have good news to share once I finish the build :. Looking for the Schematic mentioned on your facebook page. Step 5 does not seem to contain it anymore. Is there a location to obtain the latest board schematic? It will replace the original main controller parts on the white PCB, so it works like other cube project with a develop board assist. Code and circuit are the same as original design.
Hi, it was a connection to build in programmer, I planned not to use the build in programmef so I removed it. Left it blank and use a external programmer, I will sent a main controler to you guys soon, it works more stable, pls refer to the facebook page for new updates.
As it is right now, I must press button 0 on the remote in order to activate my animation. I would like the cube lights to start on the custom animation and then I could activate the pre-made animation by pressing button 2 when I desire.
I am using my created animation to turn on when an alarm is activated from an Arduino, but the cube seems to always start at the default animation aka Button 2. I don't how to edit the firmware code for your result, but the code is share on step 5, and I just added the remote code image for reference.
By WongH Store Follow. More by the author:. Features: Draw 3D Animation with software! For the controller firmware program has been used PICkit2 Programmer, but you can use any other suitable for the selected controller.
Circuit board for the project prepared by the Sprint-6 Layouts and imported in standard Gerber format. Simulation model for debugging of operation of the circuit and check the effects of the prepared environment model is designed in the Proteus Design Suite 8.
Skip to content. Star 4. LED Cube 8x8x8: software code, circuit design, simulation model. View license. Branches Tags.
0コメント